Set up instructions - Torque Link (2024)

1. Use a Windows 8 or newer laptop with good internet connection.
2. Go to https://www.flash.torquelink.com
3. Download the app
4. If warning appears, click “Keep”
5. Click on the download “torquelink.exe”
6. Window warning will likely appear click “more info” then click “run anyway”
7. Once installation completes go to desktop and run click on your new “Torque Link” app will be colors black and yellow.
8. ** IMPORTANT STEP** Firewall will likely advise warning, you must click “Allow Access”
9. Click on “Log In”
10. Click “Sign Up”
11. Sign in using email used during purchase and create a password containing (uppercase, lowercase, number and symbol) and at least 8 digits long. Once done it will say verification email sent.
12. Open your email and verify account.
13. When done properly it will say account verified
14. Usually within one business day licenses associated with your account will be added. If you are in a hurry call place of purchase and ask them to expedite it.
15. Log out of email and close internet browser.
16. Once license is added you can open Torque Link app from desktop
17. Login with user and password you created
18. Connect TL box to Vehicle, USB to Computer and Power Cord to wall. Order does not matter.
19. From here just follow on screen prompts

FLASHING YOUR VEHICLE

SNOWMOBILE-

1. Open the Torque Link application on your PC
2. If you get a JavaScript Error box you need to download the visual studio c++ 2015 redistributable otherwise proceed to step 3
   Click here to download C++ 2015
3. Read the terms and conditions and click accept if you do accept the terms
4. Log in to the TL app with your log in credentials
5. Connect the Torque Link Box to computer
6. Connect the 12v DC power supply to wall power
7. Connect Torque Link cable to snowmobile diagnostic plug
8. On (This step Ski-Doo 23 and newer only) with large interactive gauge you must pull the (Cluster) fuse in the fuse block by diagnostic plug
9. Make sure ignition/key/tether is all in the off position if your sled has an aftermarket momentary kill switch it must be held in the kill position during entire flash
10. The app should automatically connect to your Torque Link box and proceed to step 2
11. Select your active snowmobile license you want to flash
12. Click the connect button
13. Select the tune that you want to install into your vehicle that matches any performance parts you have installed, If flashing a “Development” tune this is where you would browse to your file
14. Select “FLASH ECU”
15. The counter will go from 0 to 100% (***DO NOT INTERUPT DURING FLASH***)
16. When it says “FLASH SUCCESSFUL” your ECU is flashed you may now disconnect the device
17. Congrats you are now done If you have Polaris 22 up model see below
    

*** Attention 2022, 2023 and 2024 Boost, 9R and 850 Owners ***
If you have an updated 24 and lose RPM on 7S gauge after installing BMP flash you must update the 7S to this file. 2024 7S UPDATE
If you have an updated 22 or 23 and lose RPM on 7S gauge after installing BMP flash you must update the 7S to this file. 2022 and 2023 7S UPDATE
Download the file to your PC
Using a 2G or larger USB flash drive – save the file to the drive then follow the directions below.
On your vehicle:
1. Connect the USB flash drive to the USB cable and power up your vehicle.
2. On the RIDE COMMAND touchscreen, select the SETTINGS menu by pressing the Polaris icon at the top of the screen.
3. Select GENERAL SETTINGS and then UPDATE SOFTWARE.
4. Select the file you wish to load (use the file you downloaded in the above link).
5. Select YES to restart the display. A restart is required.
Once the 7S update has been performed, load your Torque Link 7S boost adjust tune.
BOOM! Happy Hills/Trails!

UTV-

1. Open the Torque Link application on your PC
2. If you get a JavaScript Error box you need to download the visual studio c++ 2015 redistributable otherwise proceed to step 3
   Click here to download C++ 2015
3. Read the terms and conditions and click accept if you do accept the terms
4. Log in to the TL app with your log in credentials
5. Connect the Torque Link Box to computer
6. Connect Torque Link cable to snowmobile diagnostic plug
7. Remove the fuses for power steering, speedo and ride command if present
8. Make sure ignition is in the run position
9. The app should automatically connect to your Torque Link box and proceed to step 2
10. Select your active UTV license you want to flash
11. Click the connect button
12. Select the tune that you want to install into your vehicle that matches any performance parts you have installed, If flashing a “Development” tune this is where you would browse to your file
13. Select “FLASH ECU”
14. The counter will go from 0 to 100% (***DO NOT INTERUPT DURING FLASH***)
15. When it says “FLASH SUCCESSFUL” your ECU is flashed you may now disconnect the device
16. Congrats you are now done

FREQUENTLY ASKED QUESTIONS

1. No connection to sled – Verify you are using windows 8 or newer computer with current updates (as of this time Apple in windows mode is glitchy).
2. No connection to sled – verify firewall is not stopping connection temporarily turn off firewall or create exemption for Torque Link
3. No connection to sled – Verify you have a good internet connection. If poor connection get closer to router.
4. Program is glitchy – verify your computer is in good working order and not bogged down by multiple programs using all available memory. (Any new windows 8/10 laptop will run the program we have tried the cheapest acer and it will work great)
5. Program stalls (Snowmobile only) – Verify ignition switch is off, kill switch is off and tether is unplugged. Fuel pump can try to power if ignition is left on and stall flash.

SKI-DOO 850 & 850T TROUBLE SHOOTING